||For the control of broadleafed weeds in fallow before direct drilling or sowing of cereals and pastures; and in cereal crops, pastures, sugar cane, peanuts and non-agricultural areas.This is a PHENOXY HERBICIDE that can cause severe damage to susceptible crops such as cotton, grapes, tomatoes, oilseed crops and ornamentals.
||Before opening, carefully read Directions for Use, Precautionary Statements, Safety Directions and First Aid Instructions.|
Boom Spraying - Use 30-120 L/ha water.
Aerial Spraying - Use 10-90 L/ha water.
Equipment Maintenance and Usage
Equipment that has been used for this chemical should not be used for the application of other materials to sensitive plants, unless it has been well washed out with hot soapy or 1% solution of ammonia, followed by several clear water rinses.
This product may be tank mixed with Dicamba, Flowable Diuron, Chlorsulfuron (750g/kg), Gramoxone, Propon, Maizina 900 WDG, Spray-seed, Picloram and Tribunex.
DO NOT apply under weather conditions, or from spraying equipment, that may cause spray to drift onto nearby susceptible plants/crops, cropping lands or pastures. Avoid spray drift onto susceptible crops such as cotton, tobacco, tomatoes, vines, fruit trees, vegetables, legume crops and pastures, oilseed crops and susceptible trees (e.g. Kurrajongs, Belahs and Eucalypts).
DO NOT use unless wind speed is more than 3 kilometres per hour and less than 15 kilometres per hour as measured at the application site. DO NOT apply with smaller than coarse to very coarse spray droplets according to the ASAE S572 definition of standard nozzles.
||DO NOT spray if rain seems likely within 6 hours or if strong winds prevail.
DO NOT apply if crop or weeds are stressed due to dry or excessively moist conditions.
||Sipcam Amine 625 Selective Herbicide is a member of the Phenoxys group of herbicides. Sipcam Amine 625 has the Disruptors of plant cell growth mode of action. For weed resistance management, Sipcam Amine 625 is a Group I herbicide. Some naturally occurring weed biotypes resistance to Sipcam Amine 625 and other Group I herbicides may exist through normal genetic variability in any weed population. The resistant individuals can eventually dominate the weed population if these herbicides are used repeatedly. These resistant weeds will not be controlled by Sipcam Amine 625 or other Group I herbicides. Since the occurrence of resistant weeds is difficult to detect prior to use, Sipcam Pacific Australia Pty Ltd accepts no liability for any losses that may result from the failure of Sipcam Amine 625 to control resistant weeds.
|Protection of wildlife, fish, crustaceans and environment
||DO NOT contaminate streams, rivers or waterways with the chemical or used containers.
|Protection of crop, native and other non-target plants
||DO NOT spray in high winds. DO NOT spray cereals if lucerne is present. DO NOT spray crops or weeds outside the stages indicated in the "Critical Comments" as damage, loss of yield or inadequate weed control may result.
|Protection of livestock
||Low hazard to bees. May be applied at any time as recommended in the Directions for Use.
||Poisonous if swallowed. Avoid contact with eyes and skin. DO NOT inhale spray mist. When preparing spray, wear PVC or rubber apron, elbow length PVC gloves and face shield. When using the prepared spray, wear face shield. If product on skin, immediately wash area with soap and water. After use and before eating, drinking or smoking, wash hands, arms and face thoroughly with soap and water. After each day's use, wash gloves, face shield and contaminated clothing.
||If poisoning occurs, contact a doctor or Poisons Information Centre (Phone Australia: 13 11 26).
||Store in the closed, original container in a cool, well ventilated area. Do not store for prolonged periods in direct sunlight.
||Triple rinse containers before disposal. Add rinsings to the spray tank. Do not dispose of undiluted chemicals on site. If recycling, replace cap and return clean containers to recycler or designated collection point. If not recycling, break, crush, or puncture and deliver empty packaging to an approved waste management facility. If an approved waste management facility is not available, bury the empty packaging 500 mm below the surface in a disposal pit specifically marked and set up for this purpose, clear of waterways, desirable vegetation and tree roots, in compliance with relevant local, state or territory government regulations. Do not burn empty containers or product.
Empty contents fully into application equipment. Close all valves and return to point of supply for refill or storage.